Custom-designed hydraulic and electric assembly presses, 10–1000 kN, for uses including insertion of bushings and metal inserts and sheet metal straightening.
Angle roll machines (section benders) that roll or bend angle iron, T-, U- and I-beams and tubes into specific shapes or angles.
Tube bending machines for forming exhaust pipes, fuel lines, airframe components, structural supports and pipeline systems.
Dishing presses that form dished or rounded shapes in metal, used for boiler and pressure vessel heads.
Blanking lines, mechanical progressive-die presses, transfer and multi-station presses, press lines, tryout systems, press hardening and hydroforming systems for automotive mass production.
C-frame, stamping, servo, knuckle-joint and mechanical transfer presses, with coil feeding, blank loaders and electronic transfers, for production of sheet metal parts.
Hydraulic single presses and press lines, including drawing and stamping presses, fine blanking presses, composites presses, press hardening, hydroforming, tryout and forging systems.
Presses and hammers for cold, warm and hot forging, including screw, crank and hydraulic forging presses and linear hammers, plus process and die development.
Hydraulic presses for metal forming: AP&T Servohydraulic Press, ODEN multi-purpose presses and tool changing systems. Standard program 1000–50000 kN; higher forces custom-built.
Mechanical stamping-bending machines of the RM and GRM series (incl. RM 40K, RM 40P, RM 30K, GRM 80E, GRM 80P) for making stamped and bent parts from strip and wire.
Servo-controlled stamping-bending machines RM-NC, GRM-NC and BNC 4 for making stamped and bent parts; the BNC 4 is tool-compatible with MRP machines.
Linear machines LM 2000-KT (cam-controlled, up to 500 rpm) and LM 2000-NC (servo-controlled, up to 250 rpm) with 2,000 mm processing length.
Fastener clinching systems in two lines: VersaForce servo-driven closed-loop oil actuators and OHMA air-over-oil intensifiers, each in robotic and manual press variants.
OHMA air/oil intensifier piercing cylinders (2 to 70 tons) and presses (4 to 70 tons) for piercing, forming, riveting, staking, shearing and blanking.
Electric servo press for press-fitting and caulking. It stores up to 100,000 press curves and 99 pressurization parameter sets, which can be adjusted remotely over fieldbus.
Servo presses of the aiPRESS series (aiPRESS 3, 15, 36, 100 and aiPRESS JM joining modules) for joining and press-fitting, 3 kN to 100 kN. Over 1000 presses in use.
IntelliPress bench-top electric press with a ball screw drive, rated up to 12,000 lbs across three sizes, for compression or tension pressing.
Hot isostatic presses (HIP), cold isostatic presses (CIP) and isostatic food processing equipment, from small research machines to extra-large machines, with a test center for customer samples.
Automatic die clamping systems for press machines that replace bolt tightening: hydraulic clamps, all-pneumatic systems, hydraulic units, die lifters, die push cylinders and control panels.
Press machines, listed within Nidec's mechanical equipment category.
MPH range of presses for producing metal powder components by powder metallurgy.
Multi-function combination machines for can bodies performing parting, shaping, necking, flanging, beading and seaming at low, medium and high speeds.
Multi-die presses and associated curling and lining machines for the production of can ends and shells.
Automated pressing systems for ceramic tile and slab production, including the Genesis and Superfast lines, with in-body decoration during the forming phase.
Forming units for punching, bending and clinching, including clinching units, form-and-pierce clamps, suspension strut hole punches and servo-electric cylinders.
Endformers, end finishers, tube benders and integrated machining systems sold as Wauseon TubeTech. Five endformer series cover ferrous, non-ferrous and plastic tube up to 76.2 mm outside diameter.
Production system for louver, flat, oil-cooler and turbulator fins from aluminium, stainless steel or copper strip 10–110 mm wide; up to 180 cuts/min single-track.
Systems combining press machines that form material under pressure with dies and peripheral equipment such as coil processing lines and robot transfer lines.